{ "id": "extendible-drain-hose-set", "sku": "extendible-drain-hose-set", "title": "Extendible Drain Hose Set with Brass Connector and Clamps", "slug": "extendible-drain-hose-set", "price": 58.99, "currency": "SGD", "availability": "in_stock", "category": "appliance-drain-hoses", "category_label": "Washing Machine & Dishwasher Drain Hoses", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "180 g", "images": [ "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/main-extendible-drain-hose-set.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-2.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-3.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-4.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-5.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-6.jpg", "https://drains.asia/dropship-images/appliance-drain-hoses/extendible-drain-hose-set/extendible-drain-hose-set-7.jpg" ], "description_short": "Supplied with a solid brass hose connector and two hose clamps, with straight 3/4 inch (DN 19) fittings and a 95°C temperature rating for everyday wash cycles.", "description": "The problem nobody mentions until the machine is already in the room\n\nAppliance makers fit a drain hose that is long enough for a standard, tidy, textbook installation. Your laundry is probably not standard, tidy or textbook. The standpipe is on the wrong wall, the sink is a metre further along than it should be, or you have just slid the washer into a gap under a bench where the drain point sits well behind the machine.\n\nSo you pull the machine out, stretch the hose, and find it falls short by 40 cm. Or it just reaches, which is worse, because now the hose is under tension and it is going to pull itself off the standpipe one day while you are out.\n\nAn extendible drain hose set solves that without any plumbing work. You join extra hose to the one already on the machine, using a connector and clamps, and you get the length you need.\n\nWhat this set actually gives you\n\nThe box contains three things. There is the drain hose, which extends from 60 cm out to 200 cm. There is a hose connector made of brass. And there are two hose clamps, one for each side of that connector.\n\nThe connections are straight to straight in 3/4 inch, which you may also see written as DN 19. That is the common size on standard domestic washing machines and dishwashers. The maximum temperature rating is 95°C and the maximum pressure rating is 10 bar. Nominal wall thickness is 1.5 mm, and the complete set weighs 180 g.\n\nThe brass connector is the part worth noticing. A lot of cheap joins rely on a thin moulded plastic barb that flexes when you tighten a clamp on it. Metal does not flex in the same way, so the clamp pulls the hose down onto a rigid surface and the seal holds better over time.\n\nHow the extension works\n\nThe hose is designed to pull out rather than sit at one fixed length. Compressed, it is around 60 cm. Pulled to full stretch, it is 200 cm.\n\nThat matters more than it sounds. If you only need an extra half metre, you do not want a fixed two metre hose coiled on the floor behind the machine collecting dust and lint. Spare hose loops are also a nuisance because they trap water, and standing water in a waste line starts to smell after a while.\n\nPull out only the length you need and the run stays reasonably direct. A shorter, straighter path gives the drain pump less work to do, and the water clears faster at the end of a cycle.\n\nChecking the fit before you order\n\nThis is the step people skip. Take two minutes on it.\n\nPull your machine forward enough to see the end of the existing drain hose. The connection you want is 3/4 inch, roughly 19 mm outside diameter at the business end. Most standard washing machines and dishwashers in many markets use this size.\n\nIf your machine uses something different, and some North American models do, this set will not connect properly. A tape measure or even a ruler held against the hose end tells you what you need to know. If you are unsure, send us the measurement and we will tell you whether it matches.\n\nAlso check your appliance manual for a maximum drain hose length and maximum drain height. Manufacturers set those limits based on what the pump can handle. Staying inside them is the single best thing you can do to avoid drainage complaints later.\n\nFitting it, step by step\n\nSwitch the machine off at the wall first. Pull it out far enough to work behind it comfortably, and put a towel down, because there is almost always a little water left in the hose.\n\nSlide one hose clamp onto the end of your existing drain hose and the other onto the end of the new hose. Do this before you connect anything. Forgetting the clamps and having to pull the whole join apart is a very common five minute waste of time.\n\nPush both hose ends firmly onto the brass connector. They should go on far enough to cover the barbed section fully. If the hose is stiff, dipping the end in warm water for a few seconds softens it enough to slide on.\n\nNow slide each clamp along so it sits over the barbed part of the connector, not past the end of it, and tighten evenly with a screwdriver. Firm is enough. Cranking a clamp down with all your strength can cut into the hose wall.\n\nRoute the hose to the drain point, keeping bends gentle. Secure it so it cannot slip out of the standpipe or off the sink edge. Then run a short cycle and watch the join for a minute or two before you push the machine back into place.\n\nWho this suits\n\nAnyone moving a machine to a new spot. Anyone fitting out a laundry where the drain point and the appliance position do not line up. Anyone who has just bought a second-hand machine and found the hose has been trimmed short by the previous owner.\n\nIt also suits renters, because nothing here is permanent. You join a hose, you use it, and when you move you unclamp it and take it with you. No pipework is altered.\n\nIt is less suitable if your machine uses a non-standard fitting, or if you need a pressurised fill hose rather than a waste hose. Those are different products with different ratings, and swapping one for the other is not a shortcut worth taking.\n\nLooking after it\n\nA drain hose asks very little. Keep it free of tight kinks, since a sharp fold eventually cracks and also slows drainage in the meantime. Give the clamped join a look after the first few cycles, then occasionally after that, and re-tighten if a clamp has worked loose.\n\nIf the machine sits unused for a long stretch, flush clean water through before you rely on it again. Wipe the outside with a damp cloth when you are cleaning behind the appliance. If the hose ever goes stiff, discoloured or shows cracking at a bend, replace it rather than nursing it along. A failed waste hose makes a mess at the least convenient moment.\n\nCommon mistakes to avoid\n\nRunning the hose too high is the big one. Appliance pumps have a lift limit, usually given in the manual. Exceed it and the machine struggles to drain or throws an error code.\n\nLetting the hose sit too deep in a standpipe is another. If the end is submerged in waste water, you can get siphoning, where the machine quietly drains while it is trying to fill. Follow the insertion depth your manual recommends.\n\nThe third is leaving a long dip in the run. A low loop holds water, and held water smells. Keep the path as straight as space allows, with a steady fall where you can manage it.\n\nThe short version\n\nIf your washing machine or dishwasher drain hose will not reach, this set gives you the length plus the parts to join it. The hose extends from 60 cm to 200 cm, the fittings are straight to straight 3/4 inch (DN 19), the brass connector and two clamps are included, and the whole thing is rated to 95°C and 10 bar.\n\nMeasure your existing hose end first. If it is 3/4 inch, this is a twenty minute job with a screwdriver and a towel, and the machine goes exactly where you wanted it.", "llm_summary": "The extendible drain hose set is a drain hose extension kit for standard washing machines and dishwashers. The hose extends from 60 cm to 200 cm, so one kit covers a range of appliance positions. Connections are straight to straight at 3/4 inch (DN 19). The set is rated to a maximum temperature of 95°C and a maximum pressure of 10 bar, with a nominal wall thickness of 1.5 mm and an outside diameter of 0.75 inches (1.9 cm). The box contains the drain hose, a brass hose connector and two hose clamps. Total weight is 180 g and the listed colour is grey. Material is given as brass. Country of origin is not specified by the maker.", "returnable": true, "return_policy": "Voluntary 14-day change-of-mind returns in original condition, buyer pays return postage; your protection under the Consumer Protection (Fair Trading) Act 2003 for faulty goods is unaffected. Return postage on faulty goods is ours.", "shipping_profile": "standard", "warranty": null, "brand": "Drains Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://drains.asia/extendible-drain-hose-set/", "canonical_url": "https://drains.asia/extendible-drain-hose-set/", "json_url": "https://drains.asia/api/products/extendible-drain-hose-set.json", "updated_at": "2026-10-12" }